Loading... Please wait...
- Home
- Boat Accessories: Deck-Cabin
- Docking
- Fender & Accessories
- Duramax Johnson Cutless Naval Brass Sleeve Bearing 2-3/4x3-3/8x11 CROW 870702100
Categories
- HOME
- ATV - UTV Parts (4 Wheeler)
- BBQ-Cooler-Kitchen-Appliances
- Boat Accessories: Deck-Cabin
- Boat Inboard I/O Engine Parts
- Boat Outboard Engine Parts
- Boat Steering & Control
- Motorcycles Dirt/Super Bikes
- Electrical
- Engine Maintenance Parts
- Fishing
- Fuel: Tank-Filter-Sender-Parts
- General Boating
- GPS Fishfinder Navigation
- Hardware
- Jetboat & PWC Watercraft Parts
- Maintenance & Care
- Paint & Accessories & Tools
- Plumbing: Pumps-Parts-Fittings
- RV Camper Outdoor Hitch Tow
- Propellers-Skeg Guard-Anodes
- Sailing-Sailboat
- Snowmobile Parts
- Sports & Recreation & Clothing
- Stereo Receiver Speaker Amps
- Trailer Parts Trailering
- Trolling Motors & Accessories
- Used Parts
- Used & Remanufactured Engines
- Ventilation: Blower-Hatch-AC
- Others
)
Product Description
BRAND: Duramax Marine Llc.
DESCRIPTION:
- Johnson Cutless¨ Naval Brass Sleeve Bearings
- 2-3/4” Shaft,3-3/8” OD, 11” Length.
FEATURES & ATRIBUTES:
- These bearings adapt equally well to strut and stern tube mounts, and are often used effectively as rudder-stock and pintle bushings.
- Bearing diameters are precision fitted to the designated shaft size with the correct clearance for efficient water lubrication.
- External brass shells are machined and polished to provide easy fitting.
- Specially formulated oil and chemical resistant nitrile rubber is securely bonded to the shell.
- Units with thin shells are available for the struts of small craft.
- Sleeve bearings are usually installed by light press-fitting and locked in place with cone-pointed set screws.
- PRECAUTION: When shrink fitting of the bearing is required, chilling must be achieved by gradual cooling to not more than minus 20¡ F (-28¡ C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or shocking the bearing while in the chilled state could cause the rubber to separate from the shell.
Manufacturer Part Number:870702100
Internal Code:426571
Returns IN NEW ITEMS accepted in 30 days"""ONLY""" if they have NOT being installed and are in similar condition as when they were shipped. If you missed parts of the item, item CANNOT be returned.
Need more info?
Ask a question.
We will answer questions in a matter of minutes.
DESCRIPTION:
- Johnson Cutless¨ Naval Brass Sleeve Bearings
- 2-3/4” Shaft,3-3/8” OD, 11” Length.
FEATURES & ATRIBUTES:
- These bearings adapt equally well to strut and stern tube mounts, and are often used effectively as rudder-stock and pintle bushings.
- Bearing diameters are precision fitted to the designated shaft size with the correct clearance for efficient water lubrication.
- External brass shells are machined and polished to provide easy fitting.
- Specially formulated oil and chemical resistant nitrile rubber is securely bonded to the shell.
- Units with thin shells are available for the struts of small craft.
- Sleeve bearings are usually installed by light press-fitting and locked in place with cone-pointed set screws.
- PRECAUTION: When shrink fitting of the bearing is required, chilling must be achieved by gradual cooling to not more than minus 20¡ F (-28¡ C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or shocking the bearing while in the chilled state could cause the rubber to separate from the shell.
Manufacturer Part Number:870702100
Internal Code:426571
Returns IN NEW ITEMS accepted in 30 days"""ONLY""" if they have NOT being installed and are in similar condition as when they were shipped. If you missed parts of the item, item CANNOT be returned.
Need more info?
Ask a question.
We will answer questions in a matter of minutes.
