Loading... Please wait...
- Home
- Boat Accessories: Deck-Cabin
- Docking
- Fender & Accessories
- Duramax 870642100 Cutless Naval Brass Sleeve Bearing 2-1/2x3-1/8x10 CORD Shaft
Categories
- HOME
- ATV - UTV Parts (4 Wheeler)
- BBQ-Cooler-Kitchen-Appliances
- Boat Accessories: Deck-Cabin
- Boat Inboard I/O Engine Parts
- Boat Outboard Engine Parts
- Boat Steering & Control
- Motorcycles Dirt/Super Bikes
- Electrical
- Engine Maintenance Parts
- Fishing
- Fuel: Tank-Filter-Sender-Parts
- General Boating
- GPS Fishfinder Navigation
- Hardware
- Jetboat & PWC Watercraft Parts
- Maintenance & Care
- Paint & Accessories & Tools
- Plumbing: Pumps-Parts-Fittings
- RV Camper Outdoor Hitch Tow
- Propellers-Skeg Guard-Anodes
- Sailing-Sailboat
- Snowmobile Parts
- Sports & Recreation & Clothing
- Stereo Receiver Speaker Amps
- Trailer Parts Trailering
- Trolling Motors & Accessories
- Used Parts
- Used & Remanufactured Engines
- Ventilation: Blower-Hatch-AC
- Others
)
Product Description
BRAND: Duramax Marine Llc.
DESCRIPTION:
- Johnson Cutless¨ Naval Brass Sleeve Bearings
- 2-1/4” Shaft, 3-1/8” OD, 10” Length.
FEATURES & ATRIBUTES:
- These bearings adapt equally well to strut and stern tube mounts, and are often used effectively as rudder-stock and pintle bushings.
- Bearing diameters are precision fitted to the designated shaft size with the correct clearance for efficient water lubrication.
- External brass shells are machined and polished to provide easy fitting.
- Specially formulated oil and chemical resistant nitrile rubber is securely bonded to the shell.
- Units with thin shells are available for the struts of small craft.
- Sleeve bearings are usually installed by light press-fitting and locked in place with cone-pointed set screws.
- PRECAUTION: When shrink fitting of the bearing is required, chilling must be achieved by gradual cooling to not more than minus 20¡ F (-28¡ C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or shocking the bearing while in the chilled state could cause the rubber to separate from the shell.
Manufacturer Part Number:870642100
Internal Code:426557
Need more info?
Ask a question.
We will answer questions in a matter of minutes.
DESCRIPTION:
- Johnson Cutless¨ Naval Brass Sleeve Bearings
- 2-1/4” Shaft, 3-1/8” OD, 10” Length.
FEATURES & ATRIBUTES:
- These bearings adapt equally well to strut and stern tube mounts, and are often used effectively as rudder-stock and pintle bushings.
- Bearing diameters are precision fitted to the designated shaft size with the correct clearance for efficient water lubrication.
- External brass shells are machined and polished to provide easy fitting.
- Specially formulated oil and chemical resistant nitrile rubber is securely bonded to the shell.
- Units with thin shells are available for the struts of small craft.
- Sleeve bearings are usually installed by light press-fitting and locked in place with cone-pointed set screws.
- PRECAUTION: When shrink fitting of the bearing is required, chilling must be achieved by gradual cooling to not more than minus 20¡ F (-28¡ C) using freezer or regular ice (DO NOT DRY ICE). NOTE: Pounding or shocking the bearing while in the chilled state could cause the rubber to separate from the shell.
Manufacturer Part Number:870642100
Internal Code:426557
Need more info?
Ask a question.
We will answer questions in a matter of minutes.
